プロが教えるわが家の防犯対策術!

初歩的な質問だと思うのですが…
Solasir10のCDがブートしてくれません。

使用している0S:Solaris10 10/07 SPRC (1~5、langの計6枚)
入れようとしているサーバ:Netra T1
今入っているOS:Solaris8

ちょっと長いですが抜き出します。
___________________________________________________
ok boot cdrom - nowin
Resetting ...

screen not found.
keyboard not found.
Keyboard not present. Using ttya for input and output.

Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
OpenBoot 3.10.24 ME, 1024 MB memory installed, Serial #11718877.
Ethernet address 8:0:20:b2:d0:dd, Host ID: 80b2d0dd.

Executing last command: boot cdrom - nowin
Boot device: /pci@1f,0/pci@1,1/scsi@2/disk@6,0:f File and args: - nowin
Drive not ready
Evaluating: boot cdrom - nowin

Can't open boot device

Boot device: disk File and args:
SunOS Release 5.8 Version Generic_108528-29 32-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
Hostname: aaa
The system is coming up. Please wait.
checking ufs filesystems
/dev/rdsk/c0t1d0s7: is clean.
/dev/rdsk/c0t0d0s7: is clean.
in.rdisc: No interfaces up
Starting IPv4 routing daemon.
starting rpc services: rpcbind done.
Setting default IPv4 interface for multicast: add net 224.0/4: gateway aaa
syslog service starting.
Print services started.
Oct 28 10:41:26 carp /usr/lib/power/powerd: powerd: failed to get idle time for console mouse
Oct 28 10:41:27 carp sendmail[208]: My unqualified host name (localhost) unknown; sleeping for retry
volume management starting.
Wnn6: Key License Server started....

Nihongo Multi Client Server (Wnn6 R2.34)
Finished Reading Files
The system is ready.
___________________________________________________

以前はokプロンプトにしてboot cdromで認識してくれたのですが、
今回は普通にあがってきてしまいます。
何が原因なのか教えて頂けるとありがたいです。

A 回答 (2件)

Executing last command: boot cdrom - nowin


Boot device: /pci@1f,0/pci@1,1/scsi@2/disk@6,0:f File and args: - nowin
Drive not ready
Evaluating: boot cdrom - nowin

この " Drive not ready "  が原因だと思います。
    • good
    • 0

もしかするとDVD-ROMドライブ自体に異常が起こっている可能性が


あります。通常に起動した場合は、使用することが可能でしょうか?
使えないようであれば故障していたり、レンズが汚れているかも
しれません。

通常起動時に使えない場合、okプロンプトで「probe-scsi-all」を実行してみて出力された際に、DVD-ROMドライブが見つからない場合ハードウェア的にDVD-ROMドライブが認識されていないことになります。

通常起動時に使える場合ですが、次に「boot cdrom」コマンドを実行
した時にDVD-ROMドライブのシークランプは点滅するでしょうか。
もししない場合bootコマンドにつけた「cdrom」パラメータで、
目的のDVD-ROMドライブが指定できていない可能性があります。
増設ドライブなどがついてハードウェアデバイス番号が
ずれた場合に起こりうる可能性があります。
デバイスがずれている場合であれば、okプロンプトで「devalias」と
コマンドを実行した際に出力されるcdromのパスを「probe-scsi-all」コマンドのDVD-ROM部分の出力結果を元に修正してあげる必要があります。
    • good
    • 0

お探しのQ&Aが見つからない時は、教えて!gooで質問しましょう!